Plumbing Essentials: A Prerequisite for Installing a Bathtub

Get Quote

The writer is making a few good pointers related to How to Install a Bathtub as a whole in the content underneath.


How to Install a Bathtub Yourself
Mounting a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old tub with a new one is also a reasonably tough project. If the old bathtub is readily easily accessible, the project can relocate rapidly; if you need to open a wall surface to remove the old bathtub and also place the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will require a helper to leave the old bathtub and embeded in the brand-new one. Ensure you have actually certified on your own for the job as well as fit attempting it. As opposed to working with a specialist to take control of a halfway-completed task, it is better to consider employing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you mount a new bath tub in your bathroom if you have currently acquired a brand-new tub and don't require to alter the arrangement of your previous supply of water pipelines.
Your devices and product list must comprise the following:
  • New Bath tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Installment


    To start with, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet features a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps system to avoid stress on the tub.
    Fit the flexible tap adapters to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the provided washers.
    Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its final placement.

    Removing Old Touches


    If you need to change old taps with new ones as a part of your installation, after that the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the limited gain access to that is typically the situation.
    Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will originate from the pipes. Once the supply pipelines have actually been removed, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming throughout this process. Once the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
    Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.

    Mounting the Bath tub


    Using the two wood boards under its feet, put the bath tub in the called for position. The wood boards are practical in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small points.
    The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the level and adjusting the feet on the bath tub till the level reads level.
    To install taps, fit all-time low of the furthest versatile faucet connector to the suitable supply pipe by making a compression sign up with; then do the very same for the various other faucet.
    Activate the water supply and inspect all joints and also new pipework for leaks and also tighten them if essential. Load the bathtub and likewise inspect the overflow electrical outlet and the regular electrical outlet for leakages.
    Ultimately, fix the bath paneling as explained in the producer's user's manual. Tiling as well as securing around the bathtub ought to wait until the bathtub has been utilized at the very least once as this will settle it right into its last placement.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will certainly require a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a link to the existing supply pipelines.
    If you need to fit a monobloc, then you will need lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place between the faucet and also the sink. Protect the tap in place with the supplier offered backnut. When the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type ought to be connected to the tap finishes first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Bath tub


    In the location where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a stiff seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, leading to complications with wetness and feasible leaks to the ceiling below.
    You can pick from a variety of coloured sealers to blend in your components and also installations. They are offered in tubes and also cartridges, and also can securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always load the bathtub with water prior to securing, to permit the motion experienced when the tub is in usage. The sealer can break fairly very early if you do not think about this movement prior to sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily readily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof sticky and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    Hopefully you enjoyed our post about Tools You Need to Install a New Bathtub . Thank you for taking the time to read our blog post. Loved our piece? Please share it. Let somebody else locate it. Thank you so much for taking the time to read it.


    Dial immediately!

    Leave a Reply

    Your email address will not be published. Required fields are marked *